Select language:
Info pages
Tools
Find products
Products
Version:
E-butik Flex (6.3)
Manufacturers»Evil Mad Science»
SKU: EMS-DIAVOLINO
Stock status: Few in stock (2pcs)
Evil Mad Science Diavolino
Description: Diavolino ("little devil") is a low-cost, easy to build Arduino-compatible development board.
Diavolino has the form factor of an Arduino Duemilanove or Arduino Pro, but with nicely rounded corners and a striking appearance.

It's a low-profile through-hole version, with a simplified design. It's based on a ATmega328P microcontroller, and comes pre-flashed with the Arduino bootloader. Open source design, with bare basics hardware.

Diavolino is sold as an easy to assemble "through hole" soldering kit. Basic electronic soldering skill is required, and you provide the soldering tools: a soldering iron and solder, plus small wire clippers. Assembly time is typically 10-30 minutes, depending on configuration and soldering skill.

To load Arduino sketches onto a Diavolino, you'll need an FTDI USB-TTL cable: DEV-0971 or an FTDI Basic Breakout board: DEV-09716 (or an equivalent USB interface). Even if you need to deploy lots of boards, you'll probably only need one cable or breakout board. You may also need the ARD-PINS1 and an IC socket DIL28-3 if you later on want to remove the ATmega328P or replace it. See related products below.

Here's what you'll find on the Diavolino circuit board:

•ATmega328P microcontroller, with Arduino bootloader
•Genuine 16 MHz crystal oscillator (better grade, 20 ppm)
•3 mm diffused red LED (naturally!), ready for blink sketch
•Auto-reset circuit
•Reset button
•Wire jumper for optional USB power
•6-pin header for USB-TTL cable
•Places to hook up to a battery box, complete with strain relief
•Locations for optional side socket strips, ICSP connector, and TO-92 regulator

Here's what you won't find on Diavolino:

•The USB interface chip- again, that's why you need the cable or basic breakout board.
•Advanced power management. Please provide power to Diavolino from one source at a time: battery, USB, or plug-in power supply.
•A separate 3.3 V regulator. Shields and accessories that require separate 3.3 V power may need assistance to work correctly.

Powering Diavolino
The ATmega328P microcontroller requires 4.5 - 5.5 V dc when operating at 16 MHz.
Diavolino can be powered from a FTDI USB-TTL-5V cable, if you hook up the wire jumper that connects that power source to the board's "Vcc" line.

You can also power the board through a 3xAA or 3xAAA battery box, or through a plug-in power supply. For most situations that require wall-plug power, we recommend to use a 5 V power supply directly. If you have a specific reason to use a higher voltage wall wart (e.g., 9 V), then you'll also have to provide a voltage regulator to make the 5 V supply for the microcontroller.

NOTE: Requires soldering!
VAT 119,00 sek
Volume discount, click here!
Click on image to enlarge
Similar products
SKU: ADA-0795
Adafruit MENTA
Description: Introducing the MENTA, a portable minty Arduino compatible project that fits into a common mint tin. We took our super popular Boarduino series and ...
Stock status: Only 1pcs in stock
VAT289,00 sek Volume discount
SKU: ARD-UNO-R3
Arduino Uno Rev 3
Description: This is the new Arduino Uno R3. In addition to all the features of the previous board, the Uno now uses an ATmega16U2 instead of the 8U2 found on the ...
Stock status: In stock (100pcs or more)
VAT199,00 sek Volume discount
SKU: BRAGE-SIP-LT
Brage SIP (lite version)
Stock status: Few in stock (7pcs)
VAT74,00 sek Volume discount
SKU: DIL28-3
DIL Socket 28-pin 0.3"
Stock status: In stock (25-49pcs)
VAT7,00 sek Volume discount
SKU: PRT-11269
Female Header Pack
Description: This pack of female headers includes two 6-pin headers and two 8-pin headers. This is similar to the header kit that comes with Arduino shields ...
Stock status: In stock (17pcs)
VAT20,00 sek Volume discount
SKU: DEV-09716
FTDI Basic Breakout - 5V
Description: This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality ...
Stock status: Few in stock (9pcs)
VAT119,00 sek Volume discount
SKU: FTBAS
LAWICEL - FTDI Basic BoB
Description: This is our own version of the "FTDI Basic Breakout Board" and works in the same way as other similar boards on the market. It is preconfigured with ...
Stock status: Temporary out of stock!
VAT79,00 sek Volume discount
SKU: DEV-09718
TTL-232R USB cable 5V IO
Description: The TTL-232R cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The I/O pins of ...
Stock status: In stock (25-49pcs)
VAT149,00 sek Volume discount
Close
Shopping cart empty
Login
Login
Password
New customer
Forgot password?

För våra Svenska kunder, använd gärna vår Svenska sida, då det finns mycket mer information där.

Orders made before 2PM CET is taken care of same day (though not Fridays, then it is 10.30AM)
Arduino Uno @ LAWICEL We have the new Arduino Uno R3 and Arduino Mega2560 in stock.
Select currency
Price excl/incl VAT
SparkFun @ LAWICEL Sensors, Breakout Boards, Wireless, Arduino etc.
Vi är ett kreditvärdigt företag enligt Soliditets värderingssystem som baserar sig på en mängd olika beslutsregler. Denna uppgift är alltid aktuell, informationen uppdateras dagligen via Soliditets databas.
Contact us If you have any questions or miss any items in the webshop you are more than welcome to contact us! Contact us
Products list
About cookies
LAWICEL AB, Box 3, SE-282 21 Tyringe, Sweden, Phone +46 451-59877